Stack FlashHobby F722 FC + 60A ESC

The FlashHobby F722 + 60A 4‑in‑1 ESC Stack is a high-performance flight control & power module designed for FPV drones. It combines the F722 flight controller (with Betaflight OSD and DJI compatibility) and a robust 60A 4-in-1 ESC, delivering a compact, integrated solution for 3S–6S LiPo setups. Ideal for freestyle, racing, or cinewhoops that demand efficient wiring and strong output.

Features:
- Plug-and-play integration reduces wiring complexity and installation time
- Full compatibility with DJI O3, RunCam Link, Caddx Vista, or DJI Air Unit V1
- Built-in OSD and telemetry support simplifies flight control setup
- Strong power handling and reliable protection (TVS, capacitor) enhance durability
- Multiple voltage outputs (5V, 9V, 3.3V) to power peripherals directly
- LED & buzzer pads for status indication and custom lighting

FC Specifications:
Product Name: FLASH HOBBY F722 30.5x30.5 Flight Controller
MCU: STM32F722RET6
IMU(Gyro): ICM42688
USB Port Type: Type-C
Barometer: BMP280
OSD Chip: BetaFlight OSD w/ AT7456E chip
DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct
6-pin DJI Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, nowireis needed to be changed
Black box: 16M Black Box
Current Sensor Input: Supported. For 50A ESC, please set scale =180 and Offset = 0
Power Input: 3S-6S Lipo (Through ESC 8-PIN connector)
5V BEC Output: 5 grous 5V output, the total current load is 3A
9V Output: 3 groups 9V output, the total current load is 2.5A
3.3V Output: 1 group 3.3V output, maxmumcurrent is 300mA
ESC Signal: M1 - M4
UART: 6 sets (UART2, UART5, UART3), ART6 (Dedicatedfor SBUS), UART4 (Dedicated for ESC telemetry), UART1 (Dedicated for VTX data setting)
Sbs: Debugging to UART6 Channel
ESC Telemetry: UART R4 (UART4)
I2C: Supported. SDA & SCL pads on front side. Usedfor
magnetometer
LED Pad: Supported. LED,5V, and GND pads on bottomof thefront side. Used for WS2812 LED controlled by
Betaflight firmware
Buzzer: supported, 5V, BZ pads for 5V Buzzer
BOOT Button:
Supported.
[A]: Press and hold BOOT button and power theFConat the same time will force the FC to enter DFUmode,
this is for firmware flashing when the FCgets bricked.
[B]: When the FC is powered on and in standby mode,
the BOOT button can be used to controller theLEDstrips connected to LED1-LED4 connectors onthebottom side. By default, short-press the BOOTbuttonto cycle the LED displaying mode. Long-press theBOOT button to switch between SpeedyBee-LEDmode and BF-LED mode. Under BF-LEDmode, all theLED1-LED4 strips will be controlled by Betaflight firmware
Supported Flight Controller Firmware: BetaFlight (Default)
Firmware Target Name: STM32F722RET6
Mounting: 30.5x30.5mm (4mm hole diameter)
Dimension: 37x37x6.6mm
Weight: 7.5g

ESC Specifications:
Product Name: FLASH HOBBY BLS 60A 30.5x30.5 4-in-1ESC
Firmware: BLS 16.7
Continuous Current: 55Ax4
Burst Current: 60A (5seconds)
TVS Protective diode: Yes
External Capacitor: 35V560uF Low ESR Capacitor (In the package)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=180 Offset=0)
ESC Telemetry: Not supported
Mounting: 30.5x30.5mm (4mm hole diameter)
Dimension: 42.3x37x6.2mm
Weight: 12g

Package includes:
1x Stack FlashHobby F722 FC + 60A ESC